Page Comparison

Health Science 217 - Level 3 Classroom - Seats 45

Powering Up the Equipment
The equipment is controlled from the lectern using a Crestron Touch a Extron Control Panel Interface.  

Image Removed

Press the On button on the Extron. After pressing ON, the button will blink red for 30 seconds while the projector turns on and warms up.  Wait until the On button turns white before selecting the desired source button on the Extron. The switcher will not receive the command to switch until after it has finished warming up.

The resident computer and document camera are powered on using the appropriate button located on each device.

Projector Standby (Pic-Mute)
Each source page (COMPUTER, LAPTOP, DOCUMENT CAMERA, VCR, & DVD) has a Projector Standby button located in the lower left corner of the screen. Pressing this button once will Press the MUTE button on the Extron once to place the projector in standby or pic-mute mode. While this mode is active, Simply press the button will flash. Simply press the button again to take the projector out of standby mode.
NOTE: If the projector is in standby mode and you press one of the source buttons (COMPUTER, LAPTOP, DOCUMENT CAMERA, DVD, etc.) the projector will be taken out of standby.

Volume
Press the VOLUME button on the Crestron to display the appropriate touch-screen controls. Volume up, down, and mute controls are provided. 

Volume
The adjustment of volume is done using the Volume knob located in the lower-left corner of the Extron.


NOTE: Computers have their own volume controls which may need to be adjusted separately.

Resident Computer @ Lectern
Press the POWER button on the resident computer to turn it on. HS  HS 217 is equipped with a HP rack-mounted Dell computer. USB ports are located next to the computerthe computer's power button.

Once the computer has been powered up, press the COMPUTER PC button on the Crestron to the Extron to display the appropriate touch-screen controls.

image on both the monitor and display  projector simultaneously.

Document Camera (ELMO)
The Doc Cam's power and lights must be turned on manually using the controls located on the camera itself. Click here for more information regarding the document camera found in this classroom.

Once the camera's power is on, press the DOC CAM button on the Crestron to the Extron to display the appropriate touch-screen controlson the projector and monitor.

Blu-ray/DVD Playback   (via the Blu-ray Player)

This room is equipped with a Blu-ray player that can play both Blu-ray and DVD player)
Press the OPEN/CLOSE button on the DVD player and insert your disc into the disc tray. Press the DVD button on the Crestron to display the appropriate touch-screen controls.  

Touch-buttons are provided which allow you to control the DVD player from the Crestron. The only time you ever touch the DVD player itself is to insert or eject your disc.VHS Playback (via the VCR)
Simply insert your tape into the VCR and press the VCR button on the Crestron to display the appropriate touch-screen controls.  discs.

1. Turn on the Blu-ray player using the power button on the player, or on the remote control.
2. Press the BLU-RAY button on the Extron Control Panel.
3. The image from the Blu-ray player will now display.
4. Open the disc tray by using the eject button on the Blu-ray player.  Insert your disc and then press the same button again to close the tray.
5. Use the remote control to control the playback of your disc.

Image RemovedImage Removed

Click on the image below to zoom	Click on the an image below to zoom
Image Added	Image Added
The VCR Blu-Ray player is in the rack	Sony Blu-Ray remote

Touch-buttons are provided which allow you to control the VCR from the DVD player from the Crestron. The only time you ever touch the VCR itself the DVD player itself is to insert or eject your tapedisc.

Connecting a Laptop
The cables HDMI cable needed for connecting a laptop computer are is found on the instructor's lectern. In addition to cables for connecting a laptop, a power outlet is also located on the lectern for your convenience.

podium.  The HDMI connection caries both video and audio.  For more information see Selecting HDMI Audio Output. 

Using the HDMI cable

Image Added

1. Plug the HDMI cable into your laptop's

HDMI port.

2. Press the

HDMI button on the Extron.

3. Turn on your laptop's power.

4. If needed, set your laptop to display on a secondary display.

Image Removed

Don't have a VGA an HDMI port on your laptop? Visit Training & Support to find out what type of adapter is needed to connect your laptop.

Auxiliary Video Input
Use the external Audio/Video cables located on the instructor's lectern to display images from a video camera or other external device; S-video and composite audio/video cables are provided. After connecting your device with the appropriate cables, press the AUX button on the Crestron to display the appropriate touch-screen controls.

Touch-buttons are provided which allow you to select your external device for playback in the room.

Powering Down the Equipment

Press the SHUTDOWN OFF button on the Crestron to display the appropriate touch-screen controls. Press the green "Yes" button to proceed with shutdown or the red "No" button to cancel.

the Extron to shut down the projector. 

The resident computer and document camera are each powered off separately. Instructions for shutting down the computer are found below.

Be sure to remove any media from the equipment before shutting it down.
Image Removed Image Removed Image Removed

 Powering Down the Resident Computer

1. Open the Start Menu (click on  in the lower-left corner).

2. Click the "Shut Down" button.