Page Comparison

Health Science 206 - Level 3 Classroom - Seats 40

Powering Up the Equipment
The ceiling-mounted LCD projector is controlled using the wall-mounted Extron Control Panel located on the wall behind the lectern.  

Click on the image below to zoom

 

Click on the image below to zoom

Image Removed

Image Added

 

Image Added

Image Removed

Instructor's lectern

 

Extron Control Panel

Press the ON button to turn on the LCD projector. After pressing ON, wait until the button has stopped flashing before selecting the desired source button on the Extron. The projector will not receive the command to switch until after it has finished warming up.

The resident computer, document camera, and DVD /VCR combo unit player are all powered on using the appropriate button located on each device.

Projector Standby (AV MUTE)
The AV MUTE button is located to the right of the display ON/OFF buttonbuttons. Pressing this button once will place the projector in standby (or pic-mute) mode, as well as mute room audio. While this mode is active, the button will flash. Simply press the button again to take the projector out of standby mode and unmute the audio.

Volume
The adjustment of volume is done using the knob located on the Extron Control Panel. Rotate the knob clockwise to increase the audio volume or counterclockwise to decrease it. The LED lights to the left of the volume knob indicate the current audio level. The top light will flash red when the volume level is at 100%.

NOTE: Computers have their own volume controls which may need to be adjusted separately.

Resident Computer @ Lectern
Press the POWER button on the resident computer to turn it on. HS 206 is equipped with a HP computerDell computer. USB ports are located next to the computer's power button.

Once the computer has been powered up, press the PC button on the Extron to display the image on both the monitor and LCD projector simultaneously.

Click on the image below to zoom

Click on the image below to zoom

Image Removed

Image Added	Image Added
The computer is in the rack

Document Camera (ELMO)
The Doc Cam's power and lights must be turned on manually using the controls located on the camera itself. Click here for more information regarding the document camera found in this classroom.

Once the camera's power is on, press the DOC CAM button on the Extron to display the image on both the monitor and LCD projector simultaneously.

DVD or VHS Tape Playback (via the DVD /VCR combo unitplayer)
Once the equipment is powered up, insert your disc or VHS tape disc into the SONY DVD /VCR combo unitplayer. The combo unit is controlled using the buttons on the unit or the corresponding SONY universal remote control provided.

Click on the image below to zoom

 

Click on the image below to zoom

Image Removed

Image Added

 

Image Added

Image Removed

The DVD

/VCR combo unit

player is in the rack

 

SONY

universal

remote control

Press the DVD /VCR button on the Extron to display the DVD /VCR image image on both the monitor and the LCD projector. To switch between DVD and VCR modes, use the DVD and VIDEO buttons found on the combo unit itself or the GUIDE button on the SONY universal remote control. 

NOTE: When using the SONY universal remote control, press the DVD button first to set the remote to use the commands programmed for the DVD/VCR. Refer to the image above for clarification on some of the functionality of the remote.point the remote control at the SONY DVD player.

Connecting a Laptop
The cables HDMI cable needed for connecting a laptop computer are is found on the instructor's lectern.  The connection caries both video and audio.  For more information see Selecting HDMI Audio Output. 

Using the

VGA cable

HDMI cable

 

Image Added

1. Plug the

VGA cable

HDMI cable into your laptop's

VGA

HDMI port.

Image Removed

Image Added

2. Plug the Ethernet cable into your laptop's network jack (if needed).

 Image Removed

 Image Removed

4.

3.

 Plug the audio cable into your laptop's headphone jack.

Press the LAPTOP button on the Extron.

 5

4. Turn on your laptop's power.

 6

5. If needed, set your laptop to display on a secondary display.

Don't have a VGA an HDMI port on your laptop? Visit Training & Support to find out what type of adapter is needed to connect your laptop.

Powering Down the Equipment
Press the OFF button on the Extron to turn off the LCD projector.

The resident computer, document camera, and DVD /VCR combo unit player must be powered off separately. Instructions for shutting down the computer are found below.

Be sure to remove any media from the equipment before shutting it down.
Image Removed Image Removed Image Removed

 Powering Down the Resident PC

1. Open the Start Menu (click on  in the lower-left corner).

2. Click the "Shut Down" button.