OM 203

1. When the Canisius Logo Screen appears, tap the screen to start.

2. The ceiling-mounted LCD projector will begin to warm up and the motorized screen will lower.

3. Once the projector has finished warming up, the Extron will display the Main Menu.

Please Note: If not left powered on from the prior class, the resident computer, document camera, and lectern monitor must each be powered on separately. Instructions for doing so will be found in the appropriate section below.

Room lighting can be controlled by using the wall plates (located behind the lectern and by both doors) or by using the Extron Touch Panel.

To access the lighting controls from the Extron, press the Lighting Control button to display the appropriate control screen. After selecting the desired preset, press the X in the upper right corner to exit this screen.

The motorized projection screen automatically lowers and raises at system start and shutdown. In addition, it can be manually controlled by using the wall plate (located behind the lectern) or by using the Extron Touch Panel.

To access the screen controls from the Extron, press the Screen Control button to display the appropriate control screen. After adjusting the screen, press the X in the upper right corner to exit this screen.

Projector Standby is used to temporarily hide the image on the projection screen.

Press the Projector Standby button, located in the lower right of the touch panel screen, to activate it; the button will flash red while this mode is active. Simply press the button again to take the projector out of standby and display the image on the projection screen.

Volume is controlled using the Extron Touch Panel. Volume up, down, and mute buttons are located on the right-side of the touch panel screen. These controls are accessible regardless of which source is selected for display.

1. Power on the resident computer, which is located in the equipment rack inside the lectern. The button is located on the right-side of the computer.

2. Press the COMPUTER button on the Extron Touch Panel.

3. The image from the computer will now display on the ceiling-mounted LCD projector and lectern monitor.

1. Power on the document camera by using the slider located on the right-side of the unit near the back.

2. Press the DOCUMENT CAMERA button on the Extron Touch Panel.

3. The image from the document camera will now display on the ceiling-mounted LCD projector and lectern monitor.

1. Press the BLU-RAY PLAYER button on the Extron Touch Panel.

2. The image from the Blu-ray player will now display on the ceiling-mounted LCD projector and lectern monitor.

3. Open the disc tray by using the OPEN/CLOSE button on the Extron's Blu-ray Player page or on the player itself. Insert your disc and then press the same button again to close the tray.

Blu-ray and DVD playback controls are located on the left-side of the screen, while disc navigation and other functions (subtitle, display) are on the right-side of the screen.

The only time you ever need to touch the Blu-ray player itself is to insert or eject your disc.

1. Plug the HDMI cable into your laptop's HDMI port.

2. Press the LAPTOP button on the Extron Touch Panel to display the image from the laptop on the ceiling-mounted LCD projector and lectern monitor.

Don't have a HDMI port on your laptop?
Click here to view what type of adapter you need and where to get it on campus.
Network Access
Both wired (using the provided Ethernet cable) and wireless connectivity are available in this classroom. Instructions for connecting to the wireless network can be found on Confluence here.

1. Press the SHUT DOWN button on the Extron Touch Panel to power off the equipment.

2. Press "Yes" to proceed with the shutdown or "No" to cancel and resume use of the room.

3. The ceiling-mounted projector will begin to cool down, the Blu-ray player will power off, and the motorized screen will raise. Once the projector has finished cooling down, the Extron will display the Canisius Logo screen and the room can be turned back on.

Please Note: The resident computer, document camera, and lectern monitor must each be powered off separately.

The document camera is turned off by using the same slider used to turn it on. Instructions for shutting down the computer are found below.

Be sure to remove any media from the equipment before shutting it down.