Versions Compared

Old Version 2

changes.mady.by.user Pamela Dart

Saved on

compared with

New Version Current

changes.mady.by.user Nathan Johnson

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Comment: links

 Photos

Click on any image below to zoom
 

Image Added

SH 1011 seats 18 students.

Image Added

SH 1011 is equipped with one whiteboard.

Image Added

Lighting controls, along with a phone,
are located by the door.

Using the Floor Pockets

Click on any image below to zoom
 

Image Added

Additional electrical outlets can be found inside the floor pockets located on the floor of the room.

Image Added

Pull up on the handle to unlatch the cover.

Image Added

Pull open the cover fully to access
the inside of the floor pocket.

Image Added

Plug the power cord for your device into
one of the available electrical outlets.

Image Added

A sliding door is located on either
side of the floor pocket cover.

Image Added

Slide the door clockwise to open it. This
will allow you to close the floor pocket
cover while having cables connected.

Image Added

To ensure that the cover closes flush,
make sure the two "teeth" opposite the handle
are seated properly into the floor pocket.

Image Added

Floor pocket closed properly
with a power cord connected.



Science Hall 1011 - Level 2 Classroom - Seats 18

Equipment
 
Room Features
• Crestron Hard-Button Control Panel
• Ceiling-mounted LCD projector
• Ability to connect a presenter's laptop
• Motorized projection screen
 

• Seats 18 8
• Tablet arm desks/Workbenches and chairs
• Light switches by door
• Internet and network access
• Phone (wall-mounted by door)
• Whiteboard (front wall)

Powering Up the Equipment
The equipment is controlled from the flip down shelf using a black multi-button Crestron Control Panel. 

Click on the image below to zoom
 
Click on the image below to zoom

Image Added

 

Image Added

Flip down shelf
 
Crestron Control Panel


Press the POWER ON button on the Crestron. After pressing POWER ON, wait until the button has stopped flashing before selecting the desired source button on the Crestron. The projector will not receive the command to switch until after it has finished warming up.


Projector Standby (PIC-MUTE)
Press the DISPLAY MUTE button on the Crestron once to place the projector in standby mode. Simply press the button again to take the projector out of standby.

Volume
The adjustment of volume is done using the knob located on the Crestron.

NOTE: Computers have their own volume controls which may need to be adjusted separately.

Projection Screen
Use the screen control wall plate, found beneath the whiteboard tray, to operate the motorized screen. UP, DOWN, and STOP buttons are provided.


Connecting a Laptop
The wall plate and cables (VGA, HDMI, and DisplayPort-to-HDMI) needed for connecting a laptop computer are found inside the flip down shelf. In addition to cables for connecting a laptop, a power outlet is also located inside the flip down shelf for your convenience.

Using the VGA connection
 
Using the HDMI connection
   
1.
 Plug
 Plug the VGA cable into the VGA port ("PC IN") on the wall
plate inside
plate inside the flip down shelf.
 
1.
 Plug
 Plug the HDMI cable into the HDMI port ("HDMI IN") on the wall
plate inside
plate inside the flip down shelf. If using the DP-to-HDMI cable, plug the HDMI end into the wall plate.
2.
 Plug
 Plug the VGA cable into your laptop's VGA port.
 
 
  
2. Plug the HDMI cable into your laptop's HDMI port. If using the DP-to-HDMI cable,
 plug
 plug the DisplayPort end into your laptop's DisplayPort.
3.
 Plug
 Plug the appropriate end of the audio cable into the audio jack on the wall
plate and
plate and the other
end into
end into your laptop's headphone jack.
 4
3. Press the
VGA 3
HDMI button on the Crestron.
 
4. Press the
HDMI
VGA button on the Crestron.
  
4. Turn on your laptop's power.
5. Turn on your laptop's power.
 
   
5. If needed, set your laptop to display on a secondary display.
6. If needed, set your laptop to display on a secondary display.
  


Click on the image below to zoom

Inside the flip down shelf is a wall plate used for
connecting a laptop for display on the LCD projector


Don't have a VGA or HDMI port on your laptop? Visit Training & Support to find out what type of adapter is needed to connect your laptop.


Powering Down the Equipment
Just below the POWER ON button is a POWER OFF button. Press it to turn off the LCD projector and raise the motorized screen. The POWER OFF button will flash until the projector is ready to be used again. Make sure to disconnect the cables from the wall plate before closing the flip down shelf.


Auto-Shutdown
The projector will display the following image when it is not receiving a signal from a connected device:


If the projector does not receive a signal for 15 minutes, the projector will shut off automatically. The POWER ON button on the Crestron will remain lit and the motorized screen will remain down. Simply press POWER ON to turn the projector back on or press POWER OFF to properly shut down the equipment and raise the screen

.

Using the Floor Pockets

Click on any image below to zoom
 Additional electrical outlets can be found inside the floor pockets located on the floor of the room.
Pull up on the handle to unlatch the cover.
Pull open the cover fully to access
the inside of the floor pocket.
Plug the power cord for your device into
one of the available electrical outlets.
A sliding door is located on either
side of the floor pocket cover.

Slide the door clockwise to open it. This
will allow you to close the floor pocket
cover while having cables connected.

To ensure that the cover closes flush,
make sure the two "teeth" opposite the handle
are seated properly into the floor pocket.

Floor pocket closed properly
with a power cord connected

.