Page Comparison

Health Science 220 - Level 3 Classroom - Seats 40

Powering Up the Equipment
The ceilingThe ceiling-mounted LCD projector is projector is controlled using the EPSON remote controlMEDIABRIDGE control panel on the wall to the left of the whiteboard.  

Click on the image below to zoom

 

Click on the image below to zoom

Image Removed

Image Added

 Image Removed

Image Added

Instructor's lectern

 EPSON remote

MEDIABRIDGE control panel

Press On the MEDIABRIDGE control panel, under POWER press the ON button to turn on the LCD projector. After pressing ON, wait until the projector has warmed up before selecting the desired source button on the EPSON remote control panel. The projector will not receive the command to switch until after it has finished warming up.

The resident computer, and document camera , DVD/VCR combo unit, and amplifier are all powered on using the appropriate button located on each device.NOTE: The MASTER POWER switch, located at the top of the rack behind the lectern, must be turned on in order to use the technology in the room.

Projector Standby (PIC-MUTE)
Press the A/V MUTE button Ø button under SOURCE on the EPSON remote MEDIABRIDGE control panel once to place the projector in standby mode. Simply press the button again to take the projector out of standby.

Volume
If not already onOn the MEDIABRIDGE control panel under VOLUME, press the POWER button on the amplifier to turn it on. The adjustment of volume, however, is actually done using the knob located on the top of the lectern.

up arrow to increase the volume, and the down arrow to decrease volume.

NOTE: Computers have their own volume controls which may need to be adjusted separately.

Resident Computer @ Lectern
Press the POWER button on the resident computer to turn it on. HS 220 is equipped with a HP computerDell PC computer. USB ports are located next to the computer's power button.

Once the computer has been powered up, press the COMPUTER HDMI button on the EPSON remote MEDIABRIDGE control panel until the projector is set to COMPUTER 1 HDMI 1 mode to display the image on both the monitor and LCD projector simultaneously.

Click on the image below to zoom

Image Removed

Image Added

The computer is located on the left shelf inside the lectern

Document Camera (ELMO)
The Doc Cam’s power and lights must be turned on manually using the controls located on the camera itself. Click here for more information regarding the document camera found in this classroom.

Once the camera's power is on, press the COMPUTER comp button on the EPSON remote control until the projector is set to COMPUTER 1 COMPUTER 1 mode to display the image on both the monitor and LCD projector simultaneously.

DVD or VHS Playback (via the DVD/VCR combo unit)
Once the equipment is powered up, insert your disc or tape into the JVC DVD/VCR combo unit. The combo unit is controlled using the buttons on the unit or the corresponding JVC remote control provided.

Connecting a Laptop
The cables HDMI cable needed for connecting a laptop computer are is found on the instructor’s lectern. In addition to cables for connecting a laptop, a power outlet is also located on the lectern for your convenienceinstructor's podium.  The HDMI connection caries both video and audio.  For more information see Selecting HDMI Audio Output.

Using the

VGA cable

HDMI cable

 

Image Added

1.

 

Plug the

VGA cable

HDMI cable into your laptop's

VGA

HDMI port.

Image Removed

Image Added

2.

 Plug

Plug the

audio

Ethernet cable into your laptop's

headphone jack

network jack (if needed).

 Image Removed

3.

 Press

Press the

COMPUTER button

HDMI button on the EPSON

remote

control

until

panel to toggle the projector

is set

to

COMPUTER 1

HDMI 2 mode.

 4. If currently powered on, turn off the document camera.
 

5. Turn on your laptop's power.

 

6. If needed, set your laptop to display on a secondary display.

Don't have a VGA have an HDMI port on your laptop? Visit Training & Support to find out what type of adapter is needed to connect your laptop.

Powering Down the Equipment
Press On the MEDIABRIDGE control panel, under POWER button twice on the EPSON remote control press the OFF button to turn off the LCD projector. The resident computer, and document camera , and DVD/VCR combo unit must be powered off separately.  Instructions for shutting down the computer are found below.
Be sure to remove any media from the equipment before shutting it down.

 Powering Down the Resident Computer

1. Open the Start Menu (click on  in the lower-left corner).

2. Click the "Shut Down" button.