Page Comparison

Old Main 414 - Level 4 Classroom - Seats 24

Powering Up the Equipment
The equipment is controlled from the lectern using a Crestron Touch Panel Interfacethe Extron Hard-Button Control Panel interface.  

If the touch panel's screen is black, touch the screen to wake the display. When the Canisius Logo Screen appears, tap the screen and enter the required Access Code (63520).  

After successfully entering the Access Code, the equipment will power-up and the Crestron will display the message "Please Wait...Projector will be ready in **". Once the projector is ready, the Crestron will display the Main Menu, further identifying the function of the hard-buttons.

The resident computer and , document camera, and Blu-Ray player are powered on using the appropriate button located on each device.Using the Dual LCD Projectors
This room is equipped with dual LCD projectors. The SMART Board's LCD projector is the main display; it powers on when the room is started.
The ceiling-mounted LCD projector is the secondary display. This projector is powered on/off by pressing the PROJECTOR button on the Crestron and then using the appropriate touch-screen controls.

Image Removed

After choosing a source button on the Crestron, you must select the display destination (SMART Board or Projector/Screen) before the image will appear. Sources sent to the SMART Board will have accompanying audio played in the room and, in the case of the resident computer and document camera, the image will also appear on the lectern monitor.Sources sent to the

Projector /Screen will not have accompanying audio. If the ceiling-mounted LCD projector has not been turned on at the "Projector Control" screen, the Projector/Screen button will be inactive until that display is powered on.Projector Standby
Each source page (COMPUTER, LAPTOP, DOCUMENT CAMERA, DVD, etc.) has a Projector Standby button located in the lower left corner of the screen. Pressing this button will place the projector in standby mode. While this mode is active, the button will flash. Simply press the button again to take the projector out of standby mode.

NOTE: This feature is used only by the ceiling-mounted LCD projector.

Volume

The adjustment of volume is done using the Volume knob located in the lower-left corner of the Extron. 

NOTE: Computers have their own volume controls which may need to be adjusted separately.

Resident Computer @ Lectern
Press the POWER button on the resident computer to turn it on. OM 414 OM 414 is equipped with a HP Dell PC computer. USB ports are located next to the computer's power button. An additional USB port is found on the plate just above the computer.

Once the computer has been powered up, press the COMPUTER button on the Crestron to display the appropriate touch-screen controls. Touch-buttons are provided which allow you to display the image on the SMART Board's LCD projector (SMART Board) or on the ceiling-mounted LCD projector (Projector/Screen). 

NOTE: You must select a display destination before an image will be displayed. Audio only plays after the SMART Board touch-button has been pressed.SMART Board Interactive Whiteboard
The SMART Board Interactive Whiteboard is connected for use with the room's resident computer. After logging in to the computer, press the COMPUTER button on the Crestron. The SMART Board software will automatically load after you log in to the computer.
The USB cable connecting the SMART Board Interactive Whiteboard (BOARD) is located just behind the Crestron Touch Panel. You can disconnect the cable and connect it for use with a laptop. Please make sure the cable is plugged back into the USB extender before leaving the room.

Image Removed

Click here for more information regarding the SMART Board Interactive Products found in this classroom.

Document Camera (ELMO)
The Doc Cam's power and lights must be turned on manually using the controls located on the camera itself. Click here for more information regarding the document camera found in this classroom.

Once the camera's power is on, press the DOC CAM button on the Crestron to display the appropriate touch-screen controls.  

Click on the image below to zoomImage Removed

This document camera can also be used with the SMART software installed on the resident computer. Turn on the resident computer and press the COMPUTER button on the Crestron. At the "Local Computer" screen, press the SMART Board touch-button to display the computer on the SMART Board's LCD projector.

Once you've logged in, open the SMART Notebook software and click the document camera icon on the toolbar. The document camera image will now appear on the screen.

Blu-ray/DVD Playback

(via the Blu-ray Player)

This room is equipped with a Blu-ray player that can play both Blu-ray and DVD

discs.

1. Turn on the Blu-ray player using the power button on the

1. player, or on the remote control.
2. Press the BLU-RAY button on the Extron Control Panel.
3. The image from the Blu-ray player will now display.
4. Open the disc tray by using the eject button on the Blu-ray player.  Insert your disc and then press the same button again to close the tray.
5. Use the remote control to control the playback of your disc.

Image Removed

Click on the image below to zoom	Click on an image below to zoom
Image Added	Image Removed
Image Removed
The VCR The Blu-Ray plater is in the rack

Connecting a Laptop
The cables HDMI cable needed for connecting a laptop computer are is found on the instructor's tablepodium.  The HDMI connection caries both video and audio.  For more information see Selecting HDMI Audio Output.  Tethered to the HDMI cable is a display port adaptor that you can use if necessary.

 Image Removed Plug the audio cable into your laptop's headphone jack.67

Using the VGA cable	HDMI cable
1. Plug Plug the VGA cable HDMI cable into your laptop's VGA HDMI port.
Image RemovedImage Added
2. Plug the Ethernet cable into your laptop's network jack (if needed).
Image RemovedImage Added
3.
4. Press the LAPTOP button on the Crestron to view the "Laptop" screen.
5. Press the "SMART Board" touch-button to display the image on the SMART Board's LCD projector.
Press the HDMI button on the Extron.
4. Turn on your laptop's power.
5. If needed, set your laptop to display on a secondary display.
Click on the image below to zoom
Image Removed

Don't have a

HDMI port on your laptop? Visit Training & Support to find out what type of adapter is needed to connect your laptop

.

Use the external Audio/Video cables located on the instructor's lectern to display images from a video camera or other external device; S-video and composite audio/video cables are provided.
After connecting your device with the appropriate cables, press the AUX button on the Crestron to display the appropriate touch-screen controls. 

Touch-buttons are provided which allow you to select your external device for playback in the room.
NOTE: You must select a display destination before an image will be displayed. Audio only plays after the SMART Board touch-button has been pressed.Powering Down the Equipment

Press the

OFF button on

the Extron to shut down the flat panel. 

The resident computer and document camera are each powered off separately. Instructions for shutting down the computer are found below.

The resident computer, document camera, and Blu-Ray player are each powered off separately.   Instructions for shutting down the computer are found below.

Be sure to remove any media from the equipment before shutting it down.

Powering Down the Resident Computer

1. Open the Start Menu (click on  in the lower-left corner).

2. Click the "Shut Down" button.